Recent Woodworking Project

 

Facebook

 

Highboy Project

 

The making of a Grandfather Clock

 

2b1ask1

 

Baal's Bridge Square

     

The making of a Grandfather Clock

    

The first rule of thumb of making any Long case clock is to have the movement first.  Many good woodworkers have made that mistake.  For this clock, I purchased the Kieninger 9 tube movement from Klockit below.  At $3,500 it is arguably the best new, mass produced movement available today. That cost includes the pendulum, weights and dial face.

 

clock

 

clock

The ogee feet design was typical for the period of the 1780's. 

     clock

The solid Walnut case is 8' 10" tall. The intire clock to the top of the finial is 9' 8" tall.

 

clock

Notice in the above image that the back of the clock is a solid piece of walnut, 1" thick. This is where the clock strenght is. This way when the hood is slid on and off, the whole unit is sturdy and solid.

    Corner fluted columns fitted into place.

 

clock

 

clock

               

      clock

Final fit test of the nearly completed case.  The movement is bolted to what is called the Seat Plate.  It is important that this seat plate be removeable for occasional clock smith servicing.  The case is stationary while the hood assymbly slides off and the seat plate can be slid out with the movement bolted to it after the pengulium, the 36 pounds of wieghts and 9 brass tubes are removed.

clock clock

finial

 

Starting the layout to make a Philidelphia Flame Finial.

phelidelpia flame finial

 

It's not as difficult as it looks.  This one is made of Walnut.  The trick is simply to have sharp chisels.

finial

As I was finishing up this clock project, I started making the typical lolipop flame finial but was not satisfied with it.  I scoured the internet and found little help.  Then I realized I had bought this book a couple of years back and I suddenly found the finial I wanted.  My other finial made it's way to the wood stove.

philidelphia flame finial

My only problem now is the clock is 9' 8" tall.  Making it difficult to see the hard work put into making this finial.

If you want to make this Philidelpia Flame finial, you need to get this book below from Tony Kubalak. 

highboy

 

 

clock

Just waiting for the glass to be cut for the doors.

 

clock

All finished. Glass and doors set.

This grandfather clock lower compartment was designed and built to house a small kid in case of a wolf attack when mother is away as in the Story of "The Wolf and the Seven Little Goats". (Brothers Grimm)

Having been a few years now since complete, I miss the time I had spent on this very enjoyable piece. This design had been in my head for many years prior. It was good to let it out and become part of my everyday life as the chimes ring 24 hours a day.

As I wind the weights each week, it's as though I have a lifelong friend. A difficult concept to understand for someone with little appreciation for hand made woodwork and beautiful wood.

I only hope that when I am someday unable to wind the weights and it's passed down to a loved one, they will equally appreciate it. Roger Landry, May 2012.square and compasses

 

History of   The Grandfather Clock

Today, we know these tall clocks that are set in wooden cases to be "Grandfather Clocks." But, they weren't always called that. In fact, they were first called, "Longcase Clocks" or "Coffin Clocks". So how did they acquire their current name? Read this interesting article and find out the charming history of the Grandfather Clock.
Two Scientists and a Clockmaker Contribute
Although it's usually not among his list of popular contributions to the world, Italian scientist Galileo Galilei discovered in the year 1582 that time could be told by using a pendulum. Seventy-four years later after Galileo's discovery, a Dutch scientist named Christian Huygens built the first clock that used a pendulum. However, William Clement, who was a Dutch clockmaker, realized that by lengthening the pendulum, the time on a clock was more accurate. But, the long, three-foot pendulum he created wouldn't fit into a standard-sized clock case. So, in 1670, Clement built the first "long-case" clock with a pendulum. Clocks like this were also called "Floor Clocks", for obvious reasons, as well as "Coffin Clocks" because they looked like the wooden boxes corpses were buried in. This part of the history of the Grandfather Clock is entirely true. The next part of the story is supposedly true as well. Whether it is or not, you have to agree it makes the clock's history "charming" and certainly more interesting!

Some years ago, two brothers named "Jenkins" owned and operated the George Hotel, an establishment located in rural North Yorkshire, England. In the lobby of this hotel sat a long-cased clock. It just "tick-tocked" away and kept perfect time, until... one of the Jenkins brothers died. Then, the long-cased clock wouldn't keep the correct time. It always ran behind. The surviving brother brought in clocksmith after clocksmith, but none of them could figure out what was wrong with the timepiece. It just kept running slower.

Finally, at the age of ninety years old, the remaining Jenkins brother's heart stopped ticking, and he passed away. And, on that same day, the long-cased clock that sat in the lobby of the hotel stopped ticking as well. The new owner left the clock at its location with its hands showing the very time that the second brother had died.